Valve manufacturer and supplier in China
Automatic control valve factory with shsuotevalve.com: Flow control valves are used to regulate the flow volume of passing fluid in hydraulic systems. It prevents excessive flow by limiting flow to a preselected maximum rate, regardless of changing line pressure. It is a hydraulically operated, pilot controlled, diaphragm valve. The pilot control responds to the differential pressure produced across an orifice plate installed downstream of the valve. Accurate control is assured as very small changes in the controlling differential pressure produce immediate corrective action of the main valve. Flow rate adjustments are made by turning an adjusting screw on the pilot control. SHSUOTE is the top flow conrtrol valve manufacturer in China, hydraulic flow valves provide precision flow control in 1 direction, and automatically allow unrestricted free flow in opposite direction. The valve includes an orifice plate with a holder that should be installed one to five pipe diameters downstream of the Valve. As a flow control valve supplier, we provide several orifice plate with different hole optional for each size, see the additional table for selection of orifice to guarantee accurate control of flow rate. Contact us for more details! Find additional information at valve manufacturers.
The pressure relief valve is a type of valve used to control or limit the pressure in a system or vessel. Exhaust over-pressurization to protect downstream equipment or control the upstream pressure of gas or liquid. It maintains a constant downstream pressure, regardless of fluctuating demand and sustains the upstream pressure to a pre-determined minimum. As a quality pressue relief valve manufacturer, we provide pressure reducing and sustaining valve for sale. They automatically perform two independent functions. The pressure reducing pilot responds to slight variations in downstream pressure and immediately repositions the main valve to maintain the desired downstream pressure. The pressure sustaining pilot is normally held open by the upstream pressure and close when the pressure drop to the set point. We are pressure relief valve supplier for over 18 years, the pressure control relief valve usually used in lower elevation pipeline to guarantee prior use of higher elevation area.
How to Set an Altitude Valve? Setting an altitude valve correctly is crucial to ensure proper water flow and pressure regulation in a system. Here are some steps to guide you on how to set an altitude valve: Familiarize yourself with the manufacturer’s instructions: Each altitude valve may have specific guidelines for setting it up. Make sure you read and understand these instructions thoroughly before proceeding. Determine the desired water level: Based on your system’s requirements, identify the ideal water level at which you want the altitude valve to maintain. This will depend on factors such as building height and water usage. Adjust the pilot control settings: Altitude valves typically have a pilot control that regulates their operation. Use the appropriate tools to adjust this control according to your desired water level.
NSCV- Non Slam Check Valve is used as protection against reverse flow when power failure in areas where noise pollution or water hammering is a critical issue. It can provide not only quiet performance but also low head loss. Features: High strength ductile iron body used for durability and less weight; Advanced dynamic design of single body with diffuser provides streamline flow and assures lower head loss; One of the lowest head loss check valve, big save in pumping power cost, valve disc with shorter stroker and spring reverse faster than most of check valve; Coated with powder epoxy both inside & outside for corrosion resistance; Bronze bushing reduce wearing problem during operation; Hydrodynamic design with spring ensures non slamming and water hammerless; Stainless steel spring hidden in the diffuser under protection while valve in operation; Disc will positively close before reverse flow, and maximize the closing speed up to 0.2 Sec; Installation can be vertical/horizontal/ inclined. For size DN800 and up preferred vertical installation. ·Comply with EN 558-1, ISO 5752 and EN 1092-2, ISO 7005-2 flange dimension. See more details at shsuotevalve.com.
Altitude valves are commonly used in elevated water storage tanks, reservoirs, and other structures where maintaining a specific water level or pressure is important. They help ensure a reliable water supply, prevent overflow or underflow, and protect against potential damage or loss. In addition to their use in water distribution systems, altitude valves can also be found in firefighting systems, irrigation systems, and other applications where controlled water levels or pressures are crucial. Overall, altitude valves play a vital role in maintaining water system stability by regulating water levels and pressures, ensuring efficient and effective water management.
The valve is made of DI body and DI disc; Advanced newly design with dovetail seal design and captured by epoxy on the back, with multiple raised ring to have more contact with disc but less friction during closure; The double eccentric design provides less contact area of seal with disc, and less stress at the open position of the disc; The disc design with arch shape and thru disc can provide better flow capacity, stronger and less weight . The shaft and disc connection with tangential pin which can be exchangeable and provide rigid connection; The DN 100-500MM use flat disc, and DN 600-1200MM use arch shape disc; Epoxy coated interior and exterior; Valve design meets or exceeds EN 593; Top flange connection meets ISO 5211-1982, and F/F meets EN 558-1 series 13 & 14.
