High quality amorphous metal cores manufacturer and supplier
Amorphous cores manufacturer and supplier today: Transmart is a transformer core manufacturer with years of experience, mainly providing nanocrystalline cores, amorphous cores, silicon steel cores, common mode chokes, etc. We specialized in a broad range of tape wound cores in amorphous metal materials, nanocrystalline alloys, silicon electrical steels, and mu metal nickel alloys for a wide variety of applications including solar inverters, home appliance, audio system, etc. Nanocrystalline Ribbons are thin strips of material that have been engineered at the nanoscale to possess unique properties and characteristics. These ribbons are typically made up of highly ordered crystalline structures with grain sizes on the order of a few nanometers, giving them exceptional strength and durability. See even more info on transformer core.
At present, up powder core occupies the main share in the high-end market. However, due to the complex manufacturing process of M, that is, powder core and the noble price of raw materials, the price of powder core remains high and the scope of application is restricted to a certain extent. In recent years, iron-based nanocrystalline soft magnetic powder core has attracted much attention because of its low price, simple preparation process and excellent performance. Its research is quite active, which is expected to replace the local use of up powder core and be applied in the field of high frequency.
Working magnetic flux density of Fe based amorphous alloy core: 1.35t ~ 1.40t, 1.6T ~ 1.7t for silicon steel. The weight of iron-based amorphous alloy power frequency transformer is about 130% of that of silicon steel power frequency transformer. However, even if the weight is heavy, the loss of iron-based amorphous alloy for power frequency transformer with the same capacity is 70% ~ 80% lower than that of silicon steel. Considering the loss, the total evaluation price is 89% The ability of Fe based amorphous alloy to resist power waveform distortion is stronger than that of silicon steel.
Amorphous Core is preferred choice for transformers required low losses at high frequency. We have amorphous c-cores,amorphous ribbon cores,amorphous cut cores,amorphous core transformers . Please find out more about crgo core material. There are 50% and 80% nickel iron materials available, in which we manufactures Mumetal Toroidal core and Mumetal C-core, for the applications in high quality Current Transformers and power supplies industries.
We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Nanocrystalline magnetic core is a small part with magnetic conductivity. There are nanocrystalline particles with small particles in the center of nanocrystalline magnetic core. The working principle of nanocrystalline magnetic core is to absorb the common mode current in the cable through the principle of induction heating and convert it into heat to dissipate. rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size. Read more information on transmartcore.com.
As the iron core of the transformer, generally 0.35mm thick cold-rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size.
